43 series ink
This series of ink is used exclusively as printed on the polyethylene plastic bottles have been surface-treated with and are resistant to many types of products resistance. This ink smooth surface, high gloss, color and thick, durable and strong, with fast drying, suitable for general high-speed printing. It belongs to solvent evaporation drying.
Adhesion: If the surface treatment of polyethylene bottles properly, the SSI 43 series ink should have good adhesion and resistance to anti-bleach, detergent, oil and so on. However, these characteristics need in the twenty-four hours after printing to reach high results. SSI 43 series ink for wax, alcohol, perfume oils or perfume, etc. resistance poor resistance, for Sheng load above products, please join SSI 43-C191 hardener approximately 10% increase in its resistance to resistance.
Polyethylene bottles should be printed as soon as possible after the flame treatment of the surface, so that the ink can have good adhesion, however, excessive flame treatment, the adhesion of the ink of the strong resistance of the product while the resistance is weakening.
Solvent: SSI 7000 # (standard) SSI 7200 # (drying)
Can be used for printing glass, plastic bottles, plastic detergent bottles (cans), oil drums (tank), cosmetic plastic bottles, shampoo bottles and the like.
Standard Hue Number: standard hue of this series of ink has been indicated and described in the SSI screen ink color, and can be mixed with each other and with those of other standard color halftone.
Number Number Hue Hue
43-L100 pink lemon yellow 43-Q100
43-P113 purple light yellow 43-V100
43-Y115 golden 43-E100 ultramarine
43-R100 43-B100 red colors blue
43-M100 43-G100 Green Rose
43-S125 orange 43-K100 Black
43-195 43-W100 white light syrup
Instructions:
1, the printing screen: If using 90 -120T nylon mesh, with polyurethane squeegee, the printing effect perfection.
2, dilution: Different printing equipment have different printing speeds, therefore, according to the case transferred to a diluent to adjust the fit of the drying speed. For slow and semi-automatic equipment or in hot weather, in order to maintain the stability of the ink on the screen, and can be transferred to up to 15 percent of the SSI 7000 # dry diluent.
3, Drying: This ink is to use a high-volatile solvent evaporation and drying, in aid of the flame or hot air drying just a few seconds, so that the production of up to three thousand bottles per hour, if using oven drying, then eight Celsius under ten degrees, prints only one to two minutes and dried ink film surface.
4, cleaning: You can use SSI 3000 # wash water network cleaning screen and squeegee.
5, the printing volume: Use proper dilution and printing materials, ink printed per kilogram to 40 square meters.
6, color service: to provide customers with exclusive color matching services, please provide printing materials, the use of mesh, color swatch or ink version, etc., to give a reference.
Precautions:
1), in accordance with standard health regulations and safety regulations to use this product, there should be no harm to the human body, but as other general chemicals, the use of this product should also try to avoid skin and eye are contaminated, if they splash and should be based on a large number of Rinse, and treatment.
2), indicating that this technical information and data within the company through many years of research engineers and believed to be accurate, but it does not mean that when the ink use can get the same effect, because this information is based on technical engineers test environment was developed , so when using the ink, should be workshops and operating conditions, after the actual test print and determine whether the customer fit.
Adhesion: If the surface treatment of polyethylene bottles properly, the SSI 43 series ink should have good adhesion and resistance to anti-bleach, detergent, oil and so on. However, these characteristics need in the twenty-four hours after printing to reach high results. SSI 43 series ink for wax, alcohol, perfume oils or perfume, etc. resistance poor resistance, for Sheng load above products, please join SSI 43-C191 hardener approximately 10% increase in its resistance to resistance.
Polyethylene bottles should be printed as soon as possible after the flame treatment of the surface, so that the ink can have good adhesion, however, excessive flame treatment, the adhesion of the ink of the strong resistance of the product while the resistance is weakening.
Solvent: SSI 7000 # (standard) SSI 7200 # (drying)
Can be used for printing glass, plastic bottles, plastic detergent bottles (cans), oil drums (tank), cosmetic plastic bottles, shampoo bottles and the like.
Standard Hue Number: standard hue of this series of ink has been indicated and described in the SSI screen ink color, and can be mixed with each other and with those of other standard color halftone.
Number Number Hue Hue
43-L100 pink lemon yellow 43-Q100
43-P113 purple light yellow 43-V100
43-Y115 golden 43-E100 ultramarine
43-R100 43-B100 red colors blue
43-M100 43-G100 Green Rose
43-S125 orange 43-K100 Black
43-195 43-W100 white light syrup
Instructions:
1, the printing screen: If using 90 -120T nylon mesh, with polyurethane squeegee, the printing effect perfection.
2, dilution: Different printing equipment have different printing speeds, therefore, according to the case transferred to a diluent to adjust the fit of the drying speed. For slow and semi-automatic equipment or in hot weather, in order to maintain the stability of the ink on the screen, and can be transferred to up to 15 percent of the SSI 7000 # dry diluent.
3, Drying: This ink is to use a high-volatile solvent evaporation and drying, in aid of the flame or hot air drying just a few seconds, so that the production of up to three thousand bottles per hour, if using oven drying, then eight Celsius under ten degrees, prints only one to two minutes and dried ink film surface.
4, cleaning: You can use SSI 3000 # wash water network cleaning screen and squeegee.
5, the printing volume: Use proper dilution and printing materials, ink printed per kilogram to 40 square meters.
6, color service: to provide customers with exclusive color matching services, please provide printing materials, the use of mesh, color swatch or ink version, etc., to give a reference.
Precautions:
1), in accordance with standard health regulations and safety regulations to use this product, there should be no harm to the human body, but as other general chemicals, the use of this product should also try to avoid skin and eye are contaminated, if they splash and should be based on a large number of Rinse, and treatment.
2), indicating that this technical information and data within the company through many years of research engineers and believed to be accurate, but it does not mean that when the ink use can get the same effect, because this information is based on technical engineers test environment was developed , so when using the ink, should be workshops and operating conditions, after the actual test print and determine whether the customer fit.